Is the selected text only a part of a line or is the selected text a block of entire lines?

Could you post a before and after example with a color what is selected?

My macros for moving a line up or down are not written to work on wrapped lines. So whether my macros nor your version of the Line Up macro works correct in all cases on wrapped lines.

I have today updated my macro reference file with an additional appendix which commands depends on the word-wrap mode. SelectLine is one of these commands.

You can easily watch what happens when you run the macros on a file with active word-wrap mode and View - Show Line Endings also enabled. Even better is to make the steps in the macros manually. I mean

Edit - Select Line
Edit - Cut
Key DOWN or UP ARROW
Edit - Paste

Depending if the current displayed line has a line ending or not and the displayed line above or below has a line ending or not the result is correct or totally wrong.

Much more complex macro code would be necessary to let the macros Line Down and Line Up work correct in all cases with word-wrap mode on.

The block move up/down macros will be even more complicated when it should work also with active word-wrap mode correct.

Maybe I or any other user has an idea how to handle all the possible situations correct for the 4 macros. But now I have no time to think about this really not easy job.

Without word-wrapping moving a block with restoring the selection would not be too difficult, especially when the block is always smaller than 32.000 characters because than a simple Find Up "^c" could be used to restore the just moved selection.

UE has had the Move Line Up/Down function (Alt+Shift+Up/Down) as long as I've used it (v14). I submitted suggestions that this be expanded to multiple lines. If a block of lines are selected, Alt+Shift+Up/Down would move them all as a block. I just upgraded to v16 and was disappointed to see that this still does not work.

I sent IDM a message and got a reply that it works if I use Edit | Move Line Up/Down. I just tested it and it does not work on my computer.

Does this work for anyone? If so, how?

Thanks

Moving a selected block with the commands Move Line Up/Down does not work with UE v16.30.0.1003.

But with 2 macros you can move either the current line or the currently selected block down or up by 1 line.

Please note that the macros work only with UE v14.00 or later because of macro commands MoveLineDown and MoveLineUp. Of course the commands could be replaced by my macros Move Line Down / Up (without the first 3 commands).

And the macros work only for blocks where the line termination of the last selected line is also selected, otherwise a blank line will remain after moving the block down / up.

Move Block Down (works also for a single line):

InsertMode
ColumnModeOff
HexOff
IfSel
Clipboard 9
Cut
Key DOWN ARROW
Key END
IfEof
"
"
Else
Key HOME
IfColNumGt 1
Key HOME
EndIf
EndIf
Paste
IfColNumGt 1
"
"
IfColNumGt 1
DeleteToStartofLine
EndIf
EndIf
UnixReOff
Find Up "^c"
ClearClipboard
Clipboard 0
Else
MoveLineDown
EndIf

Move Block Up (works also for a single line):

InsertMode
ColumnModeOff
HexOff
IfSel
Clipboard 9
Cut
Key UP ARROW
Key HOME
IfColNumGt 1
Key HOME
EndIf
Paste
IfColNumGt 1
"
"
IfColNumGt 1
DeleteToStartofLine
EndIf
EndIf
UnixReOff
Find Up "^c"
ClearClipboard
Clipboard 0
Else
MoveLineUp
EndIf

Reselecting the block with command Find Up "^c" works only for small blocks with up to 32.000 characters. And the macros work only for entire lines, not for long lines currently wrapped using soft wrap.